[LB1 = 1 : LB2 = 1] No memory lock features enabled. [LB1 = 0 : LB2 = 1] Further programming of Flash and EEPROM is enabled. [LB1 = 0 : LB2 = 0] Same as previous, but verify is also disabled 6 11 0x03 0x03 Mode 1: No memory lock features enabled 0x03 0x02 Mode 2: Further programming disabled 0x03 0x00 Mode 3: Further programming and verification disabled 0x0C 0x0C Application Protection Mode 1: No lock on SPM and LPM in Application Section 0x0C 0x08 Application Protection Mode 2: SPM prohibited in Application Section 0x0C 0x00 Application Protection Mode 3: LPM and SPM prohibited in Application Section 0x0C 0x04 Application Protection Mode 4: LPM prohibited in Application Section 0x30 0x30 Boot Loader Protection Mode 1: No lock on SPM and LPM in Boot Loader Section 0x30 0x20 Boot Loader Protection Mode 2: SPM prohibited in Boot Loader Section 0x30 0x00 Boot Loader Protection Mode 3: LPM and SPM prohibited in Boot Loader Section 0x30 0x10 Boot Loader Protection Mode 4: LPM prohibited in Boot Loader Section LB1 Lock bit LB2 Lock bit BLB01 Boot Lock bit BLB02 Boot Lock bit BLB11 Boot lock bit BLB12 Boot lock bit [LOW:HIGH] 8 WDTON Watchdog Timer Always On 1 EESAVE EEPROM memory is preserved through chip erase 1 SPIEN Enable Serial programming and Data Downloading 0 SUT2 Select start-up time 1 SUT1 Select start-up time 1 SUT0 Select start-up time 1 OSCSEL1 Oscillator Select 1 OSCSEL0 Oscillator Select 0 11 0x80 0x00 Watch-dog Timer always on; [WDTON=0] 0x40 0x00 Preserve EEPROM memory through the Chip Erase cycle; [EESAVE=0] 0x20 0x00 Serial program downloading (SPI) enabled; [SPIEN=0] 0x01C 0x00 Start-up time 14 CK + 4 ms; [SUT=000] 0x01C 0x01 Start-up time 14 CK + 8 ms; [SUT=001] 0x01C 0x02 Start-up time 14 CK + 16 ms; [SUT=010] 0x01C 0x03 Start-up time 14 CK + 32 ms; [SUT=011] 0x01C 0x04 Start-up time 14 CK + 64 ms; [SUT=100] 0x01C 0x05 Start-up time 14 CK + 128 ms; [SUT=101] 0x01C 0x06 Start-up time 14 CK + 256 ms; [SUT=110] 0x1C 0x07 Start-up time 14 CK + 512 ms; [SUT=111]; default value 5 DUVRDINIT Reset Value of DUVRDRegister 0 DWEN Enable debugWire 1 BOOTSZ1 Select Boot Size 0 BOOTSZ0 Select Boot Size 0 BOOTRST Select Reset Vector 1 7 0x10 0x00 DUVR mode on; [DUVR=0] 0x08 0x00 Debug Wire enable; [DWEN=0] 0x06 0x06 Boot Flash section size=256 words Boot start address=$3F00; [BOOTSZ=11] 0x06 0x04 Boot Flash section size=512 words Boot start address=$3E00; [BOOTSZ=10] 0x06 0x02 Boot Flash section size=1024 words Boot start address=$3C00; [BOOTSZ=01] 0x06 0x00 Boot Flash section size=2048 words Boot start address=$3800; [BOOTSZ=00] ; default value 0x01 0x00 Boot Reset vector Enabled (default address=$0000); [BOOTRST=0] 0xff,0xdf 0xff,0xdf 0,0x20,0x20,WARNING! These fuse settings will disable the ISP interface! 1,0x08,0x00,WARNING! Enabling DEBUGWIRE will make the ISP interface inaccessible! 0,0x20,0x20,WARNING! These fuse settings will disable the ISP interface! 1,0x08,0x00,WARNING! Enabling DEBUGWIRE will make the ISP interface inaccessible! 2 5 1 4 0x00,8.0 MHz 16384 512 128 4 9 15 50 9 9 100 0x50000000 0x58080000 3 0xaca00000 0xaca80000 3 0x58000000 3 0xace00000 3 0x99e1 0xdfff ATmega16HVB 8MHZ 1 RELEASED $1E $94 $0D 1 0x31 0 0 0x00